Contact us
Close contact box
Connect ID #
899 118 857 4
Connect ID #
899 118 857 4
Don't wait on hold. We'll call you back when it's your turn to talk with the next available .
Please enter your name  
Please enter your phone number  
Please enter a message  

Calls may be recorded for training and quality control purposes.

We are located in Virginia USA.

Thank you. We will be calling you .
We're sorry. We have encountered a problem.

Crossovers glossary

Definitions of audio terms associated with crossovers

Rockford Fosgate Punch PP8-X

Rockford Fosgate passive crossover for a Punch component set

Click on a letter below to jump to that section of the glossary.



Stereo 3-way crossover

How an active stereo 3-way crossover fits into an active system

An active system (running active) is one in which every driver (tweeter, woofer, subwoofer) is run by a separate amp channel. An active system requires a good crossover network in order to manage all the high-, mid-, and low-frequencies correctly.

Active Crosssover
An active, or electronic crossover needs power connections and goes between the receiver and the amp. It handles low-level preamp signals with its solid-state circuitry to cleanly divide the signal and send each band of frequencies in the right direction.

Active crossovers are usually adjustable (you can select the crossover points) and often have other features like bass boost circuits for subwoofers. Another bonus when using an electronic crossover is that you can independently control the relative volumes of all your different drivers.

back to top


Bandpass Filter
A bandpass filter combines a high-pass filter and low-pass filter, allowing a certain band of frequencies to pass while restricting the higher and lower frequencies. Bandpass filters can be fixed in frequency and bandwidth, or variable. Bandpass filters are often used with midrange speakers to keep very high and very low notes away.

Butterworth Filters
Butterworth filters are high quality, ultra-flat electronic filters which, unfortunately, exhibit some phase shift around the crossover point, compared to other crossover filters. Butterworth filters are the most commonly used filters for protecting drivers from playing the wrong frequencies.

back to top


A capacitor, or cap, placed in series with a speaker acts as a high-pass filter, allowing only frequencies above the crossover point to pass through.

A coil, or inductor, placed in series with a speaker acts as a low-pass filter, allowing only frequencies below the crossover point to pass through.

AudioControl 6XS

AudioControl 6XS active stereo 4-way crossover

A crossover divides an input signal into two or more outputs of different ranges of frequencies, so tweeters, speakers, and subs will each get only the range of frequencies they were designed to play. Frequencies outside each designated range are attenuated or blocked.

Crossover Point
In high-pass filters, low-pass filters, and crossovers, the crossover point is the frequency at which the level of the output signal has been reduced by 3 dB, half its power level.

Crossover Slope
The rate at which the crossover attenuates the blocked frequencies. Slope is expressed as decibels per octave. A 6 dB/octave crossover reduces power by 6 dB in every octave starting at the crossover point. An octave is double the crossover point when you're going higher in frequency, and 1/2 the crossover point when you're going lower in frequency. (For example, an octave above A440 is 880 Hz, an octave below is 220 Hz.) With slopes of 12 dB and higher, you'll hear little output beyond the crossover point.

back to top


Decibel (dB)
The standard unit of measure for expressing relative power or amplitude differences. A decibel describes the ratio between the value of a measurement and a reference point. With audio, it often represents loudness, or sound pressure level (SPL). One dB is the smallest change in loudness most people can detect. A 1 dB difference is barely noticeable, but a 10 dB difference is big — a speaker playing at 10 dB higher volume will sound roughly twice as loud.

Another dB fact: For any given set of speakers, each 3 dB increase in sound level (SPL) requires a doubling of the amplifier power.


The Helix DSP PRO digital processor includes a wide range of crossover settings

Digital Crossover
A digital crossover does all its filtering in the digital domain, and displays all your options on a menu screen, laptop, or tablet. A digital crossover offers two advantages over the analog version. First, you can set your filters much more precisely, and you'll find much greater flexibility in setting up a complex system. Second, you can store different crossover settings in memory locations, and recall them with the touch of a button — that's a big plus if you're sharing settings, or switching them for car audio competition.

back to top


back to top


In audio, "frequency" is another word for "note," or a tone's pitch. An audio device's frequency response is a measure of how well the device handles all the notes in the audible spectrum, from lowest to highest. Human hearing reportedly has a frequency response of 20 to 20,000 Hz, but the high end rolls off with age.


back to top


High-pass Filter
A high-pass filter is an electronic circuit that removes all the notes below the filter's frequency setting. A high-pass filter set at 100 Hz, for example, will allow all the signal above 100 Hz in frequency to pass through, but block all those under 100 Hz. High-pass filters are primarily used to block bass notes from distorting through car speakers and tweeters.

back to top


Inline Crossovers
In-line crossovers go between the receiver and the amplifier. They look like little cylinders with RCA connectors on each end and simply plug into your amplifier’s inputs. In-line crossovers make sure your amplifiers don’t waste energy amplifying signals you don’t want — like high frequencies to a subwoofer amp. In-line crossovers each come set to a specific frequency and can’t be adjusted. Another disadvantage of using in-line crossovers is that they react differently to different amplifiers, possibly changing their crossover points unpredictably.

back to top


back to top


back to top


Low-pass Filter
A low-pass filter is an electronic circuit that removes all the notes above the filter's frequency setting. A low-pass filter, set at 100 Hz for example, will block the notes above 100 Hz and allow those under that to pass. Low-pass filters are primarily used to keep high notes from subwoofers.

Linkwitz-Riley Crossover
A Linkwitz-Riley crossover is a professional-grade crossover, made of pairs of Butterworth filters configured as high- and low-pass filters. The result is flat response and phase coherence arround the crossover frequency. Linkwitz-Riley crossovers are often used with high-end component systems, where the phase between drivers is critical.

back to top


back to top


back to top


back to top


Audiofrog GB2510C

Audiofrog 2-way passive crossover

Passive Crossover
Passive crossovers go between the amplifier and the drivers (tweeters, speakers, and subs). A passive crossover circuit is built with coils, capacitors, and resisters beefy enough to handle the high output power of most amplifiers. Some passive crossovers include a tweeter level switch, which gives you some control over how loud the tweeter plays relative to the woofer. A disadvantage of using passive crossovers is that they filter out frequencies already amplified, creating extra heat and lowering speaker efficiency.

back to top


The Q-factor of a filter is the frequency of the crossover point divided by the width of the filtering effect. The higher the Q, the more narrow or sharper a filter's focus becomes.

back to top


back to top


Subsonic Filter
Also called an infrasonic filter, a subsonic filter cuts off extremely low bass (below the range of human hearing) that many speakers cannot effectively reproduce, thereby making the amp's power supply and output devices, and the speaker, more efficient.

back to top


Tri-Way Crossover
A tri-way crossover allows you to power a pair of stereo speakers and one subwoofer simultaneously from the outputs of a single 2-channel amplifier. It accepts the two sets of speaker wires from your amplifier, and provides three sets of speaker wires for your speakers and sub. Typically, the speakers will receive the rated stereo power of the amp above the crossover point, while the the amp's bridged power goes to the sub.

back to top


back to top


The subjective perception of how loud a sound is, or how well it fills the listening space. Volume and loudness are subjective, because everyone reacts to sound differently. A sound's pressure level (SPL), or intensity, is the objective measurement used to compare different-volume sounds.

back to top


back to top


An abbreviation for crossover.

back to top


back to top


back to top

  • Samuel Brent Gay from Grove

    Posted on 5/29/2022

    I'm an admitted [slowpoke] relating to car steres . After speaking with a Crutchfeld Technical Support agent, he recommended that for the crossovers of a DB+ 6502 component system, I input power to the crossovers for the sail tweeter & woofer for each front door with the wires from the woofer. As such below: 1) OEM woofer +/- wires to crossover input. 2) Crutchfield supplied wires from tweeter and woofer outputs to respective speakers. Repeat for opposite door's crossover, woofer, and tweeter. Dead ended oem tweeter wires. Does this method provide the power of the entire oem amp or only the power designated for the loan woofer of one front door? If the latter is correct, where might you suggest the input to the crossover be powered? Obviously, I'm nearly clueless with regard to car stereo component All help is welcomed.

    Commenter image

    Buck Pomerantz from Crutchfield

    on 5/31/2022

    Samuel, If you've talked to a Crutchfield Support Tech and don't understand their recommendations, perhaps you should ask them again for clarification, instead of someone with no familiarity with your issues.
  • Commenter image

    Buck Pomerantz from Crutchfield

    Posted on 9/19/2015

    Bob, The PP8-X is made for Rockford Fosgate's Punch Pro Series components, and yes, it would be irresponsible to try and run 350 watts of power to a device designed for 125. But just because a speaker is rated for 350 watts RMS doesn't mean you have to give it that much. And all car amplifiers can drive an 8-ohm load. Figure on it making half its rated power at 4 ohms.

  • Bob Riddle from Henjderson

    Posted on 9/19/2015

    Fosgate crossover PP8-X And associated speakers or drivers of 8 ohms. the crossovers and the tweeters work because of the switch but the drivers have no switch and fosgate has nothing that takes a 8 ohm load. They also show the crossover loaded with 2 10 inch midrange speakers rated at 350 watts each RMS and 4 tweeters rated at 50 watts each, all this on a 125 watt crossover and no information from Fosgate

Looking for
car audio crossovers?

Car Audio Crossovers Shop our selection

Find what Fits your vehicle


Checking fit...

Compare the sound