Grandson installs a new system in the family 4Runner
Car audio DIY can be a fun family affair
Finishing what he started. When we spotted a social media post about a 12-year-old who’d installed a new car stereo his grandfather bought from Crutchfield, we had to know more. We also wanted to give them the chance to add to the system.
e reached out to Jeff and his grandson, Lukas, to learn more about their experience, and to see if they wanted to complete the sound upgrade in Jeff ’s ride with new speakers. We supplied the gear, and they let us cover the installation story in person.
Being a musician himself, Jeff loves listening to music. So when his factory stereo had been reduced to FM radio as the only listening source, he just had to make a change. And he knew that his tech-savvy grandson would be up to the task.
Here's Lukas's fine work with the Kenwood stereo installed using the Toyota installation kit.
Lukas's car stereo installation
Before starting the stereo project, Lukas prepared himself by watching 4Runner dash disassembly videos on YouTube. And during the installation, Lukas used Crutchfield's vehicle-specific MasterSheet instructions (which we supplied when Jeff bought his stereo from us) to remove the decrepit factory radio.
From there, he aced the installation of the new music maker, the Kenwood Excelon DPX793BH. Now Jeff can play his CDs, link his smartphone’s music apps using the stereo's Bluetooth® connection, and enjoy even better sounding radio, thanks to the stereo's HD Radio™ tuner.
Previous work proved helpful
When we talked to Jeff about having Lukas install new Kenwood speakers to match his Kenwood stereo, we were pleasantly surprised to learn that Lukas already had experience removing the Toyota’s door panels (a requirement for installing new speakers). He’d replaced a side mirror for his Grandpa, and the panel had to come off for that.
With the speakers and some tools loaded, my crew and I headed a couple hours up the road to Reston, Virginia. While I was there for some technical guidance, Lukas, Jeff, and Jeff's wife, Pam, did the work and did it well.
Gear for Jeff's Toyota
Getting the front door speakers out was a little tricky. They were originally bolted and glued into place, so some pressure had to be applied to release them.
With a little help from Grandpa, Lukas secures the new Kenwood woofer into the door.
Installing the new Kenwood speakers
To replace the nine-year old factory speakers, we selected Kenwood component speakers up front, while sticking with 2-way speakers for the rear doors. Their power handling and excellent sound quality were a great match for the stereo, and they also fit the 4Runner's stock locations.
Beginning with the front doors
With the door panels and factory speakers removed, Lukas began installing the Kenwood component speakers. The component woofer's screw holes matched the factory mounting bracket for each door.
Lukas secured the tweeters inside the Toyota’s sail panels without modification. The foam inside the sail panel covers held the tweeters in place and prevented them from rattling around.
He used the speaker wiring adapters Crutchfield supplied with the speakers to tie into the Toyota factory wiring. Then, he tied in the tweeter wiring by using the output terminals on the woofer and bundled all the wiring together.
The Kenwood tweeters fit neatly into the foam in the Toyota's sail panels.
The Kenwood woofer has a set of terminals for the incoming signal and another for the output to feed signal to the tweeter.
Moving to the back doors
For the 2-way speakers to fit into the rear door locations, Lukas had to drill screw holes. He held the new speakers up to the door frame, marked where he wanted the new holes to be, and then drilled. Once that was done, Lukas used included wiring adapters to plug into the factory speaker connectors. The speakers fit neatly behind the panels, which Lukas, Jeff, and Pam reinstalled after a quick sound check. I say "quick", but I remember it was a little tough getting back on task, since the system sounded so good.
Pam joined the fun and reattached the door panels, under the watchful eye of her grandson.
Job well done
Lukas’s grandparents were a little worried about him finishing the installation in time for his baseball game that evening, but he pulled it off flawlessly. And we were pleased to hear that in the game, he hit his first grand-slam home run! Now that’s a good day. Getting to know this family and hearing their hilarious banter made the trip even more worthwhile.
Jeff, Pam, Lukas, Crutchfield Designer, Tami, myself, and our photographer, J.
When you and your family are ready to pick out your next DIY sound system, be sure to contact our knowledgeable Advisors.